AUTOPILOT

DrivePilot Hydraulic Pack: Includes Precision-9 Heading Sensor, NAC-1 Autopilot Computer, PUMP-1 Hydraulic Pump – 0.8L reversible hydraulic pump, Standby-Auto button and Micro-C network components.

NAC-2 Autopilot Core Pack: Comprising of the low-current NAC-2 autopilot computer, Precision-9 compass and RF-25 rudder feedback unit.

NAC-2 VRF Core Pack: Comprising of the low-current NAC-2 autopilot computer and Precision-9 compass.

NAC-3 Autopilot Core Pack: Comprising of the high-current NAC-3 autopilot computer, Precision-9 compass and RF-25 rudder feedback unit.

NAC-3 VRF Core Pack: Comprising of the high-current NAC-3 autopilot computer and Precision-9 compass.

The low-current NAC-2 autopilot computer is ideal for smaller vessels, designed to run small hydraulic drives and mechanical drives for vessels up to 10 metres (33 feet) in length. Also provides solenoid output.

The high-current NAC-3 autopilot computer is designed for vessels over 10 metres (33 feet) in length, with the ability to run heavy-duty hydraulic drive pumps & linear rams, and also provides solenoid output.

OP12 Autopilot Controller.

AP44 VRF high capacity pack. Comprising of AP44 controller, Precision-9 compass,PUMP-3 hydraulic pump and NAC-3 autopilot computer

Bluetooth juhtpult, millega saab juhtida autopilooti. Lihtne paigaldada juba paigaldatud autopiloodisüsteemidele lisaks. Sobib Lowrance (NAC-1), Simrad (AC12, AC42, AC70, AP60/70/80) ja B&G (Triton, H5000) autopilootidega.
Vastuvõtja ühendub NMEA2000 võrku ja puldi tööraadius on 30m

Randmekinnituse rihmaga saab WR10 juhtpuldi mugavalt randmele kinnitada ning kui pulti ei kasutata on ta ikkagi mugavalt käepärast.

TP sari pakub usaldusväärset juhtimist roolipinniga paatidele pikkusega kuni 32 jalga. Madal energiakasutus ja täpne juhtimisvõimekus koos minimaalse müraga, aitavad sul nautida purjetamist veelgi rohkem.

The TP22 is a reliable and robust autopilot for tiller steered boats up to 34ft in length. Low power draw and precise steering capabilities couple together with minimal noise, allowing you to enjoy some smooth sailing.

The TP32 is a reliable and robust autopilot, which has been optimised to draw as little power as possible and operate extremely quietly, making it ideal for sailboats up to 37ft.

AC85 Autopilot Cabinet. Ships with SI80 PCB assembly. Fits up to 3x AD80 or SD80 PCBs according to installation requirements.

AC80S Autopilot Computer: Drive computer for on/off or proportional control of rudder or thruster using galvanic isolated solenoids or high level current.

AC80A Autopilot Computer: Drive computer for analog signal control of rudder or a thruster using analog voltage or low level current.

AC70 Autopilot Computer for reversible motor or non galvanic isolated solenoids, 1 NMEA 0183 RX/TX port, T-connector, 2m power network cable with terminator, 0.6m pigtail male. Terminator 120 ohm male. Installation manual and mounting accessories. Supply 12-24 VDC.

The AP48 Autopilot Controller is a premium dedicated control head for Continuum autopilot systems, enhanced with modern glass helm styling.

AP44 Autopilot controller: Rotary dial course adjuster, optically bonded 4.1-inch color display

FU80 Follow UP remote unit with display, 6m factory mounted drop cable, T-connector, front bezel, installation and user manual, gasket for panel mounting, mounting screws, loose steering lever. Take command and Mode buttons. Provides course change in Auto mode.

HDMI Cable with vibration resistant and waterproof connector on one end to connect to Navico MFDs with HDMI port.

Hydraulic Ram T0 12V - The RAM T0 Hydraulic linear actuator combines a cylinder, pump, motor, clutch and reservoir in a pre-filled, sealed unit. Designed to be used on vessels fitted with mechanical primary steering that can be back driven.

JS10 Non Follow Up Joystick, designed for armrest mounting or at key positions on the vessel. Quickly switches between Auto/NFU modes. Compatible with AC70, AC80A, AC80S, AC85, NAC-3. Comes with 10m cable.

NF80 Non Follow Up remote unit with display, 6m factory mounted drop cable, T-connector, front bezel, installation and user manual, gasket for panel mounting, mounting screws. Take command and Mode buttons. Provides course change in Auto mode.

PUMP-1 Hydraulic Pump – 0.8L reversible hydraulic pump, compatible with SeaStar manual helm pumps up to 14ci

QS80 Quickstick remote unit with display, 6m factory mounted drop cable, T-connector, front bezel, installation and user manual, gasket for panel mounting, mounting screws. Take command and Mode buttons. Provides course change in Auto mode.

RF45X Is a medium duty rudder feedback unit. Current and Frequency, comes with transmission link and 2m cable.

Simrad SG-05 CAN-bus Autopiloot ühendab otse Optimus ja Optimus 360 roolimissüsteemidega, andes täielikult integreeritud juhtimise, navigeerimise ja autopiloodi süsteemi.
Optimus juhtimissüsteemil on elektrooniline tüüri andur, mis saadab signaali CAN-bus võrgu kaudu pumba kontrolli moodulisse, mis lülitab sisse hüdraulilise pumba.

SI80 Signaaliliides 4 NMEA 0183 RX/TX pordiga, sisseehitatud 12V võrgutoide, 0.6m optiline kaabel / emane. Sisaldab paigaldusjuhendit ja paigaldustarvikuid. Toide 12-24 VDC.

Bluetooth juhtpult, mille vahendusel saab juhtida autopilooti. Lihtne paigaldada juba paigaldatud autopiloodisüsteemidele lisaks. Sobib Lowrance (NAC-1), Simrad (AC12, AC42, AC70, AP60/70/80) ja B&G (Triton, H5000) autopilootidega.
Lisaks vajalik BT-1 vastuvõtja ja N2k kaablid.

Bluetooth vastuvõtja mille vahendusel saab juhtida autopilooti. Lihtne paigaldada juba paigaldatud autopiloodisüsteemidele lisaks. Sobib Lowrance (NAC-1), Simrad (AC12, AC42, AC70, AP60/70/80) ja B&G (Triton, H5000) autopilootidega.
Vastuvõtja ühendub NMEA2000 võrku ja puldi tööraadius on 30m.
Lisaks vajalik juhtpult ja N2k kaablid.

Triton Autopiloodi lisasüsteem, madal vool

NAC-1 Autopilot Computer – The brains behind the Outboard Pilot and Drive Pilot systems. It contains the steering computer and electronics for the drive unit motor and clutch.

Outboard Pilot Cable steer Pack: Includes Point-1 Heading and GPS Sensor, NAC-1 Autopilot Computer, HELM-1 cable-steer helm drive unit , Standby-Auto button and Micro-C network components.

PUMP-2: 12V DC: Reversible hydraulic gear pump. 0.8L (49 cu.in) / min. For cylinder displacement of 80 cc - 250 cc (4.9 - 15.2 cu.in) (NAC-2 / AC12 required).

PUMP-3: 12V DC: Reversible hydraulic gear pump. 1.6L (98 cu.in) / min. For cylinder displacement of 160-550 cc (9.8 - 33.5 cu.in) (NAC-3 / AC42 required).