VHF / AIS

• Display - 3.5-inch Colour TFT LCD | 320 x 240 | Backlighting
• IMO compliant class-A AIS system
• GPS Antenna Type - TNC Female
• 50 GPS Receiver Channels
• Waterproof Rating - IPX2
• Dimensions  - 205 mm (8.07 in) x 85 mm (3.35 in) x 173 mm (6.81 in) without connectors | W x H x D
• Weight - 1.16 kg (2.56 lb)
• Power Consumption - < 9 W average @ 12 VDC, < 65 W peak power @ 12 VDC
• Power Supply (Supply Voltage) - 12 / 24 V DC

Lihtne paigaldada, 2 värvi valikut, pööratud LCD öö reziim.

B&G V20S fixed mount class D DSC VHF radio: Entry level VHF radio with NMEA2000 connectivity for GPS position, backlight control and night mode grouping with B&G MFD’s. Built in GPS. Conforms to new 2018 EU Standards.

NAIS-500 + NSPL500 kompl.. Ietver GPS500 antenu un mikro-C kabeli 1,8 m (6 pēdām) un T savienotāju.

Navico 1710 VHF antena, 2,5 m (8 ft) ultraglass, quickfit @ 6dB

V5035 AIS U BRACKET WITH MOUNTING KIT

V0535 AIS GPS ANT W 10M cable

V5035 AIS 3-PIN POWER CABLE

V5035 AIS 37-PIN EXT CABLE

Navico 1770 VHF antena, 1 m (3 ft) ultraglass, quickfit @ 3dB

Navico 1720 VHF antena, 1,1 m (3 ft) nerūsējošā tērauda masta topa antena ar kronšteinu @ 3dB

This antenna is specially designed by Vesper Marine to be used with our Antenna Splitter. Up until now you´ve had to choose an AIS-tuned antenna that is optimized for the AIS frequencies but has lower performance for your VHF radio. Or you could choose an antenna that is designed for VHF radio communications but isn´t optimal for AIS. Either of those works but we´ve got a better solution. We´ve created an antenna that solves this dilemma. It has two key features that combine to make it ideal for use with our antenna splitter: Wide bandwidth of 6 MHz means it will cover 3 MHz above and below the center point; 159 MHz center frequency gives excellent performance for VHF radio (156 Mhz) and AIS (162 MHz). The result is an antenna with superior performance over other designs. It has less than 1.5:1 VSWR at 156 MHz all the way up to 162 MHz. With other VHF or AIS antennas you´ll only get low VSWR at one end of the frequency band but not both. We´ve put all of this into the same physical package as our most popular antenna. It´s perfect for installations where the lowest possible windage is a requirement. A detachable cable makes installation and maintenance easier and allows for any length cable to be used. It easily mounts on a mast but is also suitаble for mounting most anywhere with it´s included L-bracket. Example mounting locations from our customers are along side solar panels, bimini sides, on an arch, above a radar, or along the edge of a cabin top. The L-bracket can be removed allowing for even greater mounting flexibility. Specially designed 1.0m stainless steel antenna; Easily replaceable stainless steel whip if it gets lost or damaged; Optimized for sharing between VHF radio and AIS transponder; Includes SO239 socket & mounting bracket; Perfect for masthead or installations where the L-bracket suits; Easily adapted to most any installation configuration; Detachable cable allows for any length to be used.

Navico 1810 VHF antenas uzstādīšanas stiprinājums, neilona, izturīgs, quickfit ar 5 m (16 ft) vadu

Navico 1815 VHF antenas uzstādīšanas stiprinājums, nerūsējošā tērauda, quickfit ar 5 m (16 ft) vadu

The Cortex H1 Tethered Handset is the voice and calling interface used for VHF and DSC calls. The handset’s touchscreen display is the primary interface together with dedicated buttons and the Click-Wheel for swift navigation, ease of operation and single-handed use. The touchscreen is purpose-built for the harsh marine environment and is designed and manufactured for use in wet conditions and with gloves. The handset provides a screen to set up and manage the Cortex M1 hub, view AIS target data and vessel instrumentation, manage and monitor alarms and configure the remote vessel monitoring. Upgrade your Cortex M1 SOTDMA smartAIS or add additional handsets for access to key functions in more places on board. Have situational awareness and VHF communication at your fingertips, no matter where you are on your boat. The Cortex H1 comes bundled in the Cortex V1 VHF. Add additional H1 handsets for additional stations. Includes an H1 Bulkhead Bonnector and an H1 Cradle. Operating Temperature: -25°C to +55°C (-13°F to 131°F); Audio: 3W Class D amplifier, THD < 5% @ 85dBA; Screen: LCD TFT Si, 640 x 800, 24bit Colour; Touch: Capacitive, optically bonded to LCD. Glove and salt water operable; Backlight: 600 cd/m2. Ambient light sensor for auto dimming.

The Cortex H1P Portable Handset is the voice and calling interface for VHF, DSC calls and to view AIS targets. The handset’s touchscreen display is the primary interface together with dedicated buttons and the Click-Wheel for swift navigation, ease of operation and single-handed use. The touchscreen is purpose-built for the harsh marine environment and is designed and manufactured for use in wet conditions and with gloves. The handset provides a screen to set up and manage the Cortex M1 hub, view AIS target data and vessel instrumentation, manage and monitor alarms and configure the remote vessel monitoring. Upgrade your Cortex M1 SOTDMA smartAIS or add additional handsets for access to key functions in more places on board. Have situational awareness and VHF communication at your fingertips, no matter where you are on your boat. Includes an H1P Charging Cradle and non-powered H1 cradle. Operating temperature: -25°C to +55°C (-13°F to 131°F); Audio: 3W Class D amplifier, THD < 5% @ 85dBA; Screen: LCD TFT Si, 640 x 800, 24bit Colour; Touch: Capacitive, optically bonded to LCD. Glove and salt water operable; Backlight: 600 cd/m2. Ambient li; Screen: LCD TFT Si, 640 x 800, 24bit Colour; Touch: Capacitive, optically bonded to LCD. Glove and salt water operable; Backlight: 600 cd/m2. Ambient light sensor for auto dimming.

Full Class B SOTDMA with smartAIS send and receive and integrated no-loss splitter. Monitor and control onboard systems and keep alerted on board or ashore from your smartphone. Operating Temperature: -25°C to +55°C (-13°F to 131°F); Supported Protocols: AIS Class B SO-TDMA, VHF Voice, Class D DSC, ATIS (user configurable, EU region), NOAA Weather (US region); Transmitter Frequency Error: Less than 300Hz; Antenna Connector: SO239; Splitter: Max input power 25W, Insertion Loss RX 0dB, TX < 1dB; Splitter Connector: BNC (2W).

Advanced multi-station VHF with intuitive touchscreen operation. Full Class B SOTDMA with smartAIS send and receive and integrated no-loss splitter. Monitor and control onboard systems and keep alerted on board or ashore from your smartphone. Includes M1 hub, tethered H1 handset and accessories; Built-in Class B SOTDMA with no-loss antenna splitter; Built-in WiFi and Cellular connectivity on monitoring on board and ashore; Low power consumption hub; 10Hz GPS antenna; 4-inch multi-touch display with gorilla glass for maximum durability; Single hand operation with click wheel and dedicated buttons; Wet and glove capable touchscreen; Optically bonded display for wide-angle and sunlight viewability, even in the harshest midday sun; 85 dBA of crystal-clear audio; Combined AIS and VHF display with voiced alerts; Touch a vessel onscreen for direct calling (DSC). Operating Temperature: -25°C to +55°C (-13°F to 131°F); Supported Protocols: AIS Class B SO-TDMA, VHF Voice, Class D DSC, ATIS (user configurable, EU region), NOAA Weather (US region); Transmitter Frequency Error: Less than 300Hz; Antenna Connector: SO239; Splitter: Max input power 25W, Insertion Loss RX 0dB, TX < 1dB; Splitter Connector: BNC (2W).

External Cellular Antenna connects using the Cellular Antenna Patch Cable (included) to the Cortex Hub. The External Cellular Antenna offers increased range over the internal antenna. Included Cellular Patch Cable is 5m (16ft) with Male SMA to Antenna and Female SMA to the Cortex Hub. Deck mount flush and Vertical surface mount included.

External GPS Antenna for Cortex M1 with 8" (200mm) cable. This multi-constellation GNSS Antenna is designed as an external antenna for the Cortex Hub, WatchMate Vision or XB series of AIS transponders . It is IP67 and UV stable for use in a harsh marine environment. GNSS (Global Navigation Satellite System) includes GPS, GLONASS, Bei Dou and Gallileo positioning networks.

This antenna is designed for the WatchMate Vision AIS Transponder. It may also be used as a replacement antenna for an XB-8000 or XB-6000 AIS Transponder. It combines a high performance GPS antenna and a low noise amplifier into a state-of-the-art compact and fully waterproof enclosure. This innovative antenna design has two mounting options; Pole Mount or Base Mount. As well as being easy to mount it comes with a 10m (32.8 feet) cable that has a small diameter connector making it easier to route the cable through smaller holes. Fully weather proof; Ultra-high sensitivity; Compact construction; Excellent temperature stability; Small connector at one end of the cable to facilitate installation; Two mounting configurations (pole or base); Compatibility: For use only with a WatchMate Vision or as a replacement antenna for an XB-8000 or XB-6000; Construction: Compact waterproof (IPx7) housing; Dimensions: 90mm (3 1/2") diameter x 118mm (4 2/3") high when used with base mount (as shown in the photo at the top of this page); Mounting: Pole (standard 1" threaded mast) and Base included; Cable: 10 metre (32.8 ft) RG58 with SMA that connects directly to WatchMate Vision.

The Cortex External Speaker is designed for the marine environment with an IP66 ingress protection the speaker is suitable for mounting almost anywhere on board. Compact in size, the speaker features a durable and UV stable polymer housing. Rated at 70W max power output (35W RMS) with a frequency response of 120Hz-20,000Hz to deliver a full clear sound for Cortex VHF voice and unique annunciated alarms. Surface Mount through using a 74.5mm (2 15/16”) diameter hole and requiring a minimum mounting depth of 56mm (2 1/4”). Mounted Outer Diameter: 93.5mm; Frequency Range: 120hz~20khz; Impedance: 4ohm; Watts: 70 Watt; Magnet Ferrite: 4oz; Woofer Material Polypropylene Cone; IP Rating: IP66; UV Stable: Yes; Pre-wired with 6.5ft / 1.98m of cable.

LTE, 3G, WI-FI AND GSM MARINE ANTENNA – ASA – SB PB – 300 mm (12”) h – 250 mm (10”) diam. Base diameter 25 mm (1”)

weBBoat 4G Lite - SINGLE SIM - 4G/3G/LTE AND WI-FI COASTAL INTERNET ANTENNA INTEGRATED SYSTEM - ASA - SB PB - 160 mm (6,3’’) h - 138 mm (5,4”)weBBoat 4G Lite - SINGLE SIM - 4G/3G/LTE AND WI-FI COASTAL INTERNET ANTENNA INTEGRATED SYSTEM - ASA - SB PB - 160 mm (6,3’’) h - 138 mm (5,4”)

WEBBOAT 4G PLUS - Glomexi uus dual SIM 4G/WiFi antenn ja ruuter combo seade, mis võimaldab kiiret andmesidet merel kuni 20 miili kaldast.

H1 Handset Bulkhead Connector includes a mounting base, cover, waterproof cap and power cable. Connect the bulkhead connector to 12V or 24V DC.

H1P Handset Charging Cradle securely holds a Cortex H1P Portable Handset. The cradle is pre-wired for connection to 12V or 24V DC. Small SMA connector for easy installation; Pre-wired 200mm (8”) RF cable for easy servicing; Two mounting confi gurations (deck or under deck); UV stable housing provides good color stability; UV stable plastic with a zinc plated alloy base; Dimensions: 60mm x 19mm; Loom: 200mm; Color: White; Mounting: Bulkhead, pole, deck and underdeck mounting.

New front mountable design for easy installation
New Industrial Design to align with style of Lowrance MFD’s
Seamless integration with a wider B&G system through NMEA 2000 and 0183
Built in AIS Receiver
Large screen with intuitive user interface

Railblaza Cradle Adapter fits to the rear of either the H1 Cradle or the H1P Charging Cradle allowing a Railblaza StarPort attachment to be connected.

HS35 juhtmevaba käsitoru, mis annab RS90 ja RS35 VHF raadiole täieliku mobiilsuse ja intercom side võimaluse.

Esimene Simradi VHF raadio, millel on sisse ehitatud B-klassi AIS vastuvõtja ja saatja ning GPS. 

Põhiomadused: 

•             B-klassi AIS saatja ja vastuvõtja 

•             sisse ehitatud GPS

•             D-klassi DSC VHF raadio

•             NMEA 2000 ja 0183 ühilduvus

•             võimalik lisada kuni kaks HS40 juhtmevaba käsitoru 

•             suur ekraan ja intuitiivne kasutajaliides 

•             eemaldatav käsimikrofon

•             võimalik lisada väline kõlar või hailer 

AIS / VHF / FM Splitter – unique ultra low loss design with 12dB AIS amplifier gain and antenna VSWR indicator

B&G V60 Replaces the current V50 mid level VHF, updated to comply with EN 301 025 (v2.2.1)
New front mountable design for easy installation
Low profile design to align with style of B&G MFD’s
Seamless integration with a wider B&G system through NMEA 2000 and 0183
Built in AIS Receiver
Large screen with intuitive user interface
Optional wireless handsеts with inductive charging

The V60-B includes a Class B AIS transmitter and receiver, which not only receives AIS targets but also transmits your yacht’s position to nearby AIS-equipped vessels. This helps other mariners to spot your boat through any conditions, day or night. A built-in AIS receiver monitors the position of other AIS-equipped vessels, helping you to proactively avoid collisions in crowded harbours and waterways. AIS information can be viewed on the radio’s built-in screen, or overlaid on your chart or radar screen through a compatible chartplotter.

Mount your handset anywhere on the boat with the non-powered handset cradle. The cradle has a two piece design hiding the mounting hardware behind the snap cover leaving you with a clean sleek design on the helm or bulkhead. The non-powered handset cradle can be used with either the H1(tethered) or H1P (portable) handsets.

VHF masta vads 30 m (98 ft) 1720 antenai

Powered by smartAIS technology, Vision2 has safety features that can save lives. Get proactive alerts when you have potential collision situations, if your anchor drags or if there´s a man overboard situation. With its intuitive and easy to use touchscreen, scroll through the menu, zoom in and out, see vessel details and navigation data, change alarm settings and more with the most gentle of touches. Remote control your transponder from anywhere on board with your smartphone, tаblet or smartwatch using highispeed WiFi. The Vision2 enables up to eight devices connected simultaneously for greater flexibility. The Vision2 has a stylish black bezel front panel with glossy black side panels, designed to complement every helm or Nav station. Operating Temperature: -25°C to +55°C (-13°F to 131°F); Coastal outlines: World-wide included; Nr of receivers: 2 AIS, 1 DSC (timeshared); Receive sensitivity: -113 dBm (<20% PER); Number of transmitters: 1 AIS; Transmit power output: 33 dBm (2W); GPS: 50 channel with internal antenna. Supports WAAS and EGNOS. Optional external antenna is required if Vision2 is mounted without a clear view of the sky; GPS navigation rate: 50 channel with internal antenna. Supports WAAS and EGNOS. Optional external antenna is required if Vision2 is mounted without a clear view of the sky; GPS sensitivity: tracking & navigation, -142dBm acquisition (cold start); GPS accuracy: Position 2.5m CEP, SBAS 2.0m CEP; VHF antenna required: 50 ohm, 156-162MHz, max 2:1 VSWR, PL-259 connector; Serial data: 1 fully isolated USB port (mini), 1 isolated NMEA 0183 input (RS422 4800/38400 baud) 1 NMEA 0183 output (RS422 4800/38400 baud); Connectivity: NMEA 2000, NMEA 0183, USB, Wireless 802.11 b/g/n, All input NMEA 0183 sentences are repeated to the NMEA 0183 output, USB and WiFi. Ѕelected NMEA 2000 PGN´s (heading, wind, depth, speed, temperature, and log) are translated to NMEA 0183 sentences and repeated to the NMEA 0183 output, USB and WiFi. This allows a wide varie

This package is designed for installing a WatchMate XB-6000 AIS Transponder in a nav station or wheelhouse and allows you to share a single VHF antenna between your AIS transponder and VHF radio. This package is designed to replace your existing VHF antenna with our optimized AIS/VHF shared antenna but keep your existing antenna cable.

This package is designed for installing an XB-8000 AIS Transponder in a nav station or wheelhouse and allows you to share a single VHF antenna between your AIS transponder and VHF radio. This package is designed to replace your existing VHF antenna with our optimized AIS/VHF shared antenna but keep your existing antenna cable.

XB-6000 class B AIS with NMEA 2000 gateway and built-in GPS antenna (incl. external GPS antenna)

XB-8000 class B AIS with NMEA 2000, USB, WiFi (incl. external GPS antenna)